Saturday, July 2, 2016

Sherwood's S-9910 TOTL Receiver

Sherwood S-9910 Receiver 



Today we are showing off a Sherwood S-9910 Receiver we have in for a customer for a rebuild. The S-9910 Receiver was billed as Sherwoods Solid State TOTL model. Boasting a output at 20-20K with 100W .5% THD>.  Several features set the S-9910 apart such as a trifold output setup A,B and C in a multitude of combinations,  heavy duty Power Transformer with extruded heatsink assembly and multiple Phono inputs for MM and MC and handy Pre-Main out connections. Aesthetically the illumination can’t help but to remind me of 22XX series Marantz.



Power Supply/Protection PCB 0046F
The integrated power supply, protection assemblies include integrated independent speaker relays (MY48V which where updated to Low Noise type and circuit overload with a multistage fused protection Pformer.  The power supply electrolytic were updated to high temp (105C) low impedance Nichicon PW’s and high temp (105C) Panasonic FC capacitors.  All 1S2473 type diodes were updated to 4148 type and TO-220 2SD NPN transistors to MJE1503X NPN BJT’s. The large filter electrolytic was replaced with a 2200MFD low impedance high temp (105C) capacitor. 



Featuring an impressive 30,000MFD filter, these capacitors were upgrade to high quality Nippon/Chem-Con 18,000MFD capacitors for an additional 6000 microfarads of filter :)



AF Tone Control/Pre  PCB 9029B, Tape/Push PCB 9028A-PCB7120   and RIAA PCB 0046A 
The S-9910 has an integrated  variable mic control and triple tone controls with defeat features in the AF stages.  All the electrolytic were replaced with a audio grade Nichicon KA electrolytic and Nichicon Fine-Golds.  Input 1MFD electrolytic were upgraded to high grade WIMA polypropylene film capacitors. BiPolars were replaced with Nichicon VP type. 

All small signal  1681/841 NPN/PNP staged transistors were updated to match arrays of 992/1845 NPN/PNP transistors with matching the tone control initial gain stage to 1%. This is the perfect time with the push PCB9028A assembly out to clean the potentiometers and switching. 



RIAA
The RIAA stage is housed similar to some of the 22XX Marantz with the function selector control.  Initial PNP differentials were matched to 1% KSA992 transistors.  Input .47MFD electrolytic were upgraded to high quality Panasonic ECW polypropylene film capacitors. With larger 47MFD to high temp Panasonic FC and audio grade KA electrolytic within the signal path.  As above in the AF stages the  841 and 2c1708 NPN/PNP pairs were updated to 992/1845 transistors.



Driver Stages  PCB 0046BA/B/AB
Tied into an array of complimentary push-pull output transistors 2SD427’s and 2SB557 TO-3’s. Each driver is coupled via a molex slide connector to the emitter-heatsink assembly. The extruded single TO-3 mount is perpendicular to the chassis mount. 



All of the electrolytics were replaced with high temp (105C) low impedance Nichicon PW and a .47MFD high grade ECW Panasonic Polypropylene.  D602-4 1S2473 diodes updated to 4148 type and precision Bourns bias potentiometers installed.  The 945/733 BJT’s were updated to 2383/733 TO-92 BJT’s.  The differential pair is comprised of a 2SX1583 Dual Jfet.



RF PCB 0035
The top chassis mounted tuning capacitor/RF assembly is housed in a big heavy plate shielding which is good to see.  All of the BiPolars were replaced here with Nichicon VP and polars with low impedance PW’s down to .47MFD.



New LED’s using custom SMD type festoons were installed as well.



Audio Notizen


Tuesday, June 28, 2016

Marantz 1060 Integrated Amplifier 



Today we are showcasing a Marantz 1060 Integrated Amplifier.  The Marantz 1060 is by far one of the most well regarded Integrated Amplifiers of the period, highly sought and prized for its simple, yet extremely mellow, smooth sonic qualities.  Sharing a similar topography of the pre-amp and a simplified 35V regulated power supply to the Receiver variant the 2230.  Paired with something like the Marantz Imperial 6 speaker system and a nice turn table or line source and you have yourself a classic slice of Americana’ Hi-Fi! On this particular rebuild we laid an emphasis on polypropylene upgrades within the coupling/input points.



Power Supply P900
The regulated power supply consists of a simple BJT regulator and filtering network for the 35V RIAA and 27V line level circuits.  After depopulating the assembly its important to carefully remove as much of the glue debris as possible, replacing and cleaning any effected components.  



After cleaning of the PCB is done, all of the electrolytic were replaced with a high temp (105C) Panasonic FC capacitor’s. The original ceramic .01 bypass caps were replaced with a 630V .01 Panasonic ECW polypropylene and the tied 1S- type diodes replaced with a Ultra Fast UF 400# type diode. The regulating BJT 2SC1213 was replaced with a 2383 BJT.




The remaining AC filter 4700MFD capacitors was replaced with a low ESR Nichicon up to a 10,000MFD value and coupling 3000MFD capacitors replaced with two low ESR Nichicon 6800MFD capacitors for an improved bottom end and better rectification filtering.  For hardware sakes we replaced the original switch at this time as well as then tend to gum up and arch resulting in failure.  A new DPDT 7A 250V power switch with a X1Y2 Vishay safety capacitor was installed and fixed to the chassis. 




Pre-Amplifier P400
As mentioned the 1060,2230, 2245 and 2270 all share a very similar topography.  On this assembly we updated all of the NPN small signal transistors of the (GR) grouping 2SC1000 devices to a compliment of new KSC1845 transistors.

The input and output coupling films of .22 and .47MFD electrolytic and mylars were upgraded to a high grade MKP polypropylene film capacitors.  Remaining electrolytic were replaced with audio grade Nichicon KA/ Fine Gold capacitors. The coupled BiPolars were replaced with a 1MFD high grade Panasonic ECW polypropylene film capacitor. 



 In front of this assembly is the tied tone control network, which I advise pulling now to properly clean the tone and volume/balance selector potentiometers and switching. 



RIAA P900
The Marantz 1060 has an infamous phono stage, with a very linear and responsive curve and large compliment of polypropylene the RIAA has one of the best sonically designed, NPN gain staged  phono stages out there in my honest opinion.

As with many of the integrated and 22XX series Marantz, the 1060 utilizes the 2SC458 which is a notoriously bad transistor, known for noise potentials.  Small signal transistors 2SC1000 and 2SC458 were updated to 1845 compliments and H905/906 (458) matched to 1%.  The remaining electrolytic were replaced using  all Nichicon KA audio grade capacitors and original .47MFD films to a high grade MKP polypropylene film capacitors.



Drivers P700
 Using a single PCB symmetric topography the 1060 comprises the differential with a single 945 BJT, through pre-drivers and multiple circuit H705-708 and drivers H709-712 to a quasi complimentary pair of outputs.   The .47MFD input electrolytic were replaced with a high grade Panasonic ECW polypropylene film capacitor and output coupling to a 1MFD MKP polypropylene film capacitor.  Remaining electrolytic were replaced with  high temp (105C) low impedance Nichicon PW capacitors.  Both offset and bias potentiometers were replaced with precision bourns trimmers as well.  Both SVT thermal diodes and TO-3 devices were pulled and new thermal compound applied.  Bias was calibrated at 15mV VS SM detail. 




Audio Notizen



Sunday, June 26, 2016

Sansui 2000A Receiver

Sansui 2000A Receiver


Today we have a Sansui 2000A receiver to showcase.  The 2000 and 2000A/2000X are very similar models besides PCB topography, plus or minus pre amp isolation jumpers and BJT populations. Rated at a modest 35W and manufactured in 1969 this is the last of the early 2XXX series receivers. 

Rectification F1197 Ripple Filter F1195 & Aux PCB’s
The rectification/filtering and block assemblies are all located under the chassis on separate assemblies.  The F1197 had all the electrolytic replaced with a high temp (105C) long life Panasonic FR capacitors and the D003/-4 diodes replaced with Ultra-Fast 400# type diodes along with the D007 @ F1195 and remaining electrolytic.   F1220/1254 had a low impedance PW installed and two .47MFD high grade Panasonic ECW polypropylenes. 




 A new Chassis mount PW high temp (105C) was installed and increased to a 22000MFD/100V capacitor was installed in the mounting bracket  on the top of the chassis. Along with the 3X 2200/MFD 75V capacitors updated with Nichicons to 4700MFD capacitors.





AF Tone F1212 & RIAA F1235
The Tone amp is a single PCB with the multi-tone functions shared. One major issue of the 2000X series is the integration of 2SC458 transistors.  This model only had them within the driver stages but I recommend replacing them if on board. In this case due to the operating frequency the common ksc1845 has a low frequency cut off if substituted.  While this assembly is out we clean all the phenolic based rotary potentiometers and plastic switching assemblies and lubricate. 



The electrolytic on this assembly were updated to audio grade Nichicon KA Fine/Gold FG’s. and low impedance PW’s.  the films at c717/702 were updated to high grade polypropylene MKP’s



The following transistor details is applicable to the F1235 if installed, this unit used a 871 type which is more than fine.  As above the electrolytics were replaced with audio grade  Nichicon KA/FG and low impedance PW’s.  The original  .01MFD mylar’s were upgraded to a high grade Panasonic ECW polypropylene film capacitor.





Driver Stage  F1180
The driver stage is comprised of a PP quasi complimentary output design.  As mentioned earlier the F1180 assembly utilizes the 2SC458 at input transistor TR806/801 which is replaced to a 1% matched KSC1845 transistor.  The input/output coupling films were upgraded to a high grade polypropylene film capacitors (MKP) and remaining electrolytic’s replaced with audio grade Nichicon KA/FG and PW low impedance high temp(105C) capacitors.  Due to the footprint and good tracking the offset(clipping) and bias potentiometers where removed, bathed in D5 and lubricated.  Easier bias notations can be measured at each emitter resistor for a bias of 15mV versus the current draw method.  Also note their are two service bulletins published if intrinsic noise is populated in the circuit.




The integrated Protection indicator is tethered to a output device/input sensitivity 2.5A fusible network in the rear of chassis


RF Sections
The remaining RF stages were all repopulated using a high temp (105C) low impedance PW and stacked Panasonic ECQ film capacitors (1>MFD) and the tuning capacitor shaft cleaned and debris’d.




Buffed RCA Inputs




Audio Notizen












Removed BJT-Caps-Diodes






Thursday, June 23, 2016

Pioneer SX-450 Receiver

Pioneer SX-450 Receiver 



Today we have a nice, smaller Pioneer SX-450 to showcase.  The SX-450 was billed as the entry level 15W stereo receiver in the mid 70’s from Pioneer. Akin to the SX550 in topography with its single PCB PS/driver population. The SX450 is a personal favorite, yes the output is relatively low but sonically these lower wattage Pioneers sound as good as lower watt Marantz 22XX series. Very clean presentation.

Power Supply
As is noted with the SX lower wattage series they utilize single PCB population in their construction.  On this model all of the electrolytics were removed and replaced with a high temp (105C) long life
 Panasonic FC and low impedance, high temp (105C) Nichicon PW variant.  Pioneer used glue on the large vertically mounted 220MFD< capacitors, this glue was treated with lab grade anhydrous and cleaned off the PCB.  The current limiting resistor tent to bake their solder pads here so copious reflowing was necessary throughout the assembly.



The regulating BJT 2SD313 was replaced with a heavy duty MJ 15032 BJT and thermally coupled with compound again to a standalone heatsink, the tied WZ-140 diodes was updated and Q301 2SC1384 replaced with a 2690 BJ-transistor.  I do need to highlight a major discrepancy within the manual;  
SM ERROR** schematic indicates cathode of D304(WZ-140) to Base Q302 (2SD313). PCB layout indicates Emitter Q302 to anode of D304



Driver - AF Stages  - RIAA
The driver and AF stages share a single PCB with the PS circuit.  The pre-amp is integrated into a simplified tone control circuit.  The original films of .1MFD were all upgraded to a Panasonic ECW polypropylene film capacitors.   Within the power stage all of the electrolytic were replaced with low impedance Nichicon PW and audio grade Nichicon KA capacitors.  The input/coupling .47MFD films were all replaced with a high grade Panasonic ECW polypropylene film capacitors.   



The SX450 driver state is a output-capacitor-less design with a differential PNP gain stage.  The differential pair transistor Q201-204 were updated from 2SA725 transistors to 1% matched 992(bf) transistors. The final order output devices which are comprised of a quasi complimentary  of 2SD313 TO-220 transistors were all removed. New MICA and thermal compound was applied along with X4 all new  MJ15029  output transistors which are much more reliable and heavy duty TO packages. 



RF Stage
The remaining AM/FM RF stage which is housed in a single PCB along with the 3 gang variable tuning capacitor.  The Pioneer PLL (phase-locked loop) integration helps support linear and stabile tracking with modest signal pickup.  The remaining tantalum and electrolytic capacitors were updated to low impedance long life Nichicon PW capacitors.  All remaining .47-.1 tantalums were replaced with long life, low impedance Nichicon KL capacitors.


Power Switches on SX-450/550 Units
As outlined in the link below on a SX-550 we had in recently  the SX450/550 is a piggybacked Speaker Selector/Power Switch assembly.  These power switches use a low quality metal straping to conduct, these switches become heavily carbonized from arching AC line voltage upon power up and fed to the AC lamping as flickering and sizzling (ac arching.)  The best and really only solution to these switches is to truly bypass them.  Cleaning will will not suffice, it will hold temporarily but will arch after repeated use.  As photo'd a DPDt 7A power switch should be installed discretely with a properly rated UL X1Y2 safety capacitor.  I have installed several of these in this fashion and it turned out great, the switch is moved to above the serial plate where its not noticed on the rear and the AC line braided.



http://marantzhallo-fi.blogspot.com/2016/04/pioneer-sx-550-receiver-highlight.html

Audio Notizen





Monday, June 20, 2016

Marantz 250 Power Amplifier Rebuild

Marantz 250 Power Amplifier 



Today we are show casing a rare Marantz 250 Power Amplifier.  Originally manufactured in several Mark variants and the 250M and produced from 1971 to 1976 with optional case and rack mounts.  The major differences in the MK variants is the driver topography and rectification assembly.

Power Supply/Protection Assembly
The regulated power supply share a assembly with the protection circuit. Comprised of a full wave rectification path the AC 86.5V is rectified to a stable 58.5 driver rail voltage and filter through two 20,000MFD filter capacitors. Each of the capacitors was replaced with a high grade Nippon 22,000/100V filter capacitor with new bleeder resistors.  The remaining inlet is and secondaries feed a AC rail for the camping.




All of the original Axial electrolytic were replaced with Nichicon TVX (85C) capacitors and both CR rectification diodes to Ultra-Fast UF400X type diodes.   The original TO-69 type MOTO transistor was replaced with a more reliable MJE TO-220 type transistor. 



The integrated protection is a two fold, AC in rush protector upon start up and DC deviation detection circuit peak at 4.5Vdc (-/+ present at the outputs where as the output section is tied directly to the 24V relay wipers.  The original relays due to their open frame nature present many problems in the 240/250 designs.   A new low noise Omron MY2 24V was installed, significant modifications need to be done prior to relay as the coil and wiper contacts are reversed. As photo’d below you can see each coil lead was de-solder and buckled to the wiper, a very very delicate procedure!



Meter Assembly
Output from the driver sections is driven to the meter assembly to Q403 small signal transistor, protected by two small value diodes. buckled to Q404 driver, pushed a bridge rectification network that supplies the DC rails for the meter operation.  All of the capacitors were updated to a low impedance high reliability Nichon PW and zeners updated. Several of the 1/4W resistors had drifted and were replaced with carbon film KOA type.  Often times these meters will become sticky with age due to the original lubricant,  these meters were no exception and still are "reliable" at bests, the 250 is synonyms with issues, even rebuilt.






Driver Assemblies
The driver pcbs is a classic push-pull topography using parked NPN/PNP TO-3 outputs Moto SJ2520/2519 pairs.  The initial stage is comprised on a NPN/PNP compliment in a Sziklai design.  The output is then coupled to the thermally coupled differential transistor pairs Q501/502.  The gain current is driven tot he pre-drivers Q507/508 TO-69 transistors and applied to driver compliment Q510/11.



The differential pair transistors were replaced with thermally coupled performance oriented ZTK795 transistors to stabilize the DC offset and thermally coupled together.  Pre-Drivers were updated to a 1220/2690 compliment TO-220 to replace the MOTO to-69 transistors and drivers to a modified TO-220 mount MJE components.  The bias Q521 was updated to a ztx transistors, due to the solid construction the potentiometers were pulled and deeply cleaned and lubricated on this model.   All of the original axial were replaced with a audio grade Nichicon KA capacitors an MPK and input 1MFD film capacitors along with a high end WIMA polypropylene film capacitor.  




Audio Notizen